Hugo Lhachemi

Hugo Lhachemi, Christophe Prieur

This paper studies the boundary feedback stabilization of a class of diagonal infinite-dimensional boundary control systems. In the studied setting, the boundary control input is subject to a constant delay while the open loop system might exhibit a finite number of unstable modes. The proposed control design strategy consists in two main steps. First, a finite-dimensional subsystem is obtained by truncation of the original Infinite-Dimensional System (IDS) via modal decomposition. It includes the unstable components of the infinite-dimensional system and allows the design of a finite-dimensional delay controller by means of the Artstein transformation and the pole-shifting theorem. Second, it is shown via the selection of an adequate Lyapunov function that 1) the finite-dimensional delay controller successfully stabilizes the original infinite-dimensional system; 2) the closed-loop system is exponentially Input-to-State Stable (ISS) with respect to distributed disturbances. Finally, the obtained ISS property is used to derive a small gain condition ensuring the stability of an IDS-ODE interconnection.

Hugo Lhachemi, Robert Shorten

This paper deals with the establishment of Input-to-State Stability (ISS) estimates for infinite dimensional systems with respect to both boundary and distributed disturbances. First, a new approach is developed for the establishment of ISS estimates for a class of Riesz-spectral boundary control systems satisfying certain eigenvalue constraints. Second, a concept of weak solutions is introduced in order to relax the disturbances regularity assumptions required to ensure the existence of classical solutions. The proposed concept of weak solutions, that applies to a large class of boundary control systems which is not limited to the Riesz-spectral ones, provides a natural extension of the concept of both classical and mild solutions. Assuming that an ISS estimate holds true for classical solutions, we show the existence, the uniqueness, and the ISS property of the weak solutions.

Hugo Lhachemi, Christophe Prieur, Robert Shorten

This paper discusses the robustness of the constant-delay predictor feedback in the case of an uncertain time-varying input delay. Specifically, we study the stability of the closed-loop system when the predictor feedback is designed based on the knowledge of the nominal value of the time-varying delay. By resorting to an adequate Lyapunov-Krasovskii functional, we derive an LMI-based sufficient condition ensuring the exponential stability of the closed-loop system for small enough variations of the time-varying delay around its nominal value. These results are extended to the feedback stabilization of a class of diagonal infinite-dimensional boundary control systems in the presence of a time-varying delay in the boundary control input.

Hugo Lhachemi, David Saussié, Guchuan Zhu et al.

This note establishes the Exponential Input-to-State Stability (EISS) property for a clamped-free damped string with respect to distributed and boundary disturbances. While efficient methods for establishing ISS properties for distributed parameter systems with respect to distributed disturbances have been developed during the last decades, establishing ISS properties with respect to boundary disturbances remains challenging. One of the well-known methods for well-posedness analysis of systems with boundary inputs is the use of a lifting operator for transferring the boundary disturbance to a distributed one. However, the resulting distributed disturbance involves time derivatives of the boundary perturbation. Thus, the subsequent ISS estimate depends on its amplitude, and may not be expressed in the strict form of ISS properties. To solve this problem, we show for a clamped-free damped string equation that the projection of the original system trajectories in an adequate Riesz basis can be used to establish the desired EISS property.

Hugo Lhachemi, David Saussié, Guchuan Zhu

This paper addresses the boundary stabilization of a flexible wing model, both in bending and twisting displacements, under unsteady aerodynamic loads, and in presence of a store. The wing dynamics is captured by a distributed parameter system as a coupled Euler-Bernoulli and Timoshenko beam model. The problem is tackled in the framework of semigroup theory, and a Lyapunov-based stability analysis is carried out to assess that the system energy, as well as the bending and twisting displacements, decay exponentially to zero. The effectiveness of the proposed boundary control scheme is evaluated based on simulations.

Hugo Lhachemi, David Saussié, Guchuan Zhu

This note deals with the boundary control problem of a nonhomogeneous flexible wing evolving under unsteady aerodynamic loads. The wing is actuated at its tip by flaps and is modeled by a distributed parameter system consisting of two coupled partial differential equations. Based on the proposed boundary control law, the well-posedness of the underlying Cauchy problem is first investigated by resorting to the semigroup theory. Then, a Lyapunov-based approach is employed to assess the stability of the closed-loop system in the presence of bounded input disturbances.

Ammar Malik, Hugo Lhachemi, Robert Shorten

I-nteract is a cyber-physical system that enables real-time interaction with both virtual and real artifacts to design 3D models for additive manufacturing by leveraging on mixed reality technologies. This paper presents novel advances in the development of the interaction platform I-nteract to generate 3D models using both constructive solid geometry and artificial intelligence. The system also enables the user to adjust the dimensions of the 3D models with respect to their physical workspace. The effectiveness of the system is demonstrated by generating 3D models of furniture (e.g., chairs and tables) and fitting them into the physical space in a mixed reality environment.

Ammar Malik, Hugo Lhachemi, Robert Shorten

This paper presents I-nteract, a cyber-physical system that enables real-time interaction with real and virtual objects in a mixed augmented reality environment to design 3D models for additive manufacturing. The system has been developed using mixed reality technologies such as HoloLens, for augmenting visual feedback, and haptic gloves, for augmenting haptic force feedback. The efficacy of the system has been demonstrated by generating 3D model using a novel scanning method to 3D print a customized orthopedic cast for human arm, by estimating spring rates of compression springs, and by simulating interaction with a virtual spring using hand.

Hugo Lhachemi, Ammar Malik, Robert Shorten

Our objective in this paper is to review the application of feedback ideas in the area of additive manufacturing. Both the application of feedback control to the 3D printing process, and the application of feedback theory to enable users to interact better with machines, are reviewed. Where appropriate, opportunities for future work are highlighted.