Myeongbo Park

Myeongbo Park, Junhyun Park, Ihsan Ullah et al.

Flexible endoscopic robots enable minimally invasive access through natural orifices, but their control accuracy is limited by configuration-dependent hysteresis in the tendon-sheath mechanisms (TSMs). Tendon-sheath friction and tendon elasticity induce a systematic discrepancy between the proximal actuation input and distal output, and this discrepancy varies with the insertion tube configuration. To address this challenge, this paper proposes the Self-Sensing Tendon Loop (SSTL), a double-pass tendon loop routed through the insertion tube and wrapped around a distal pulley, and returned to the proximal end. The loop structure allows both the input and output tensions of the SSTL to be measured proximally, thereby providing an input-output tension profile without requiring distal force or fiber-optic sensors. Because the SSTL shares the same routing path as the actuation TSM, the two TSMs exhibit strongly correlated hysteresis behaviors. From the SSTL tension profile, a learning-based mapping estimates the configuration-dependent hysteresis parameters of the actuation TSM, which are then used by a feedforward controller to compensate for actuation hysteresis. We validate the proposed method by tracking actuation tendon tension under three different insertion tube configurations. Across sinusoidal and random trajectories, the proposed method reduces average RMSE by 88.1% compared with the uncompensated baseline, achieving 97.8% of the performance of direct identification, which requires direct measurement of the input and output tension profile of the actuation TSM.

Junhyun Park, Chunggil An, Myeongbo Park et al.

Continuum manipulators in flexible endoscopic surgical systems offer high dexterity for minimally invasive procedures; however, accurate pose estimation and closed-loop control remain challenging due to hysteresis, compliance, and limited distal sensing. Vision-based approaches reduce hardware complexity but are often constrained by limited geometric observability and high computational overhead, restricting real-time closed-loop applicability. This paper presents a unified framework for markerless stereo 6D pose estimation and position-based visual servoing of continuum manipulators. A photo-realistic simulation pipeline enables large-scale automatic training with pixel-accurate annotations. A stereo-aware multi-feature fusion network jointly exploits segmentation masks, keypoints, heatmaps, and bounding boxes to enhance geometric observability. To enforce geometric consistency without iterative optimization, a feed-forward rendering-based refinement module predicts residual pose corrections in a single pass. A self-supervised sim-to-real adaptation strategy further improves real-world performance using unlabeled data. Extensive real-world validation achieves a mean translation error of 0.83 mm and a mean rotation error of 2.76° across 1,000 samples. Markerless closed-loop visual servoing driven by the estimated pose attains accurate trajectory tracking with a mean translation error of 2.07 mm and a mean rotation error of 7.41°, corresponding to 85% and 59% reductions compared to open-loop control, together with high repeatability in repeated point-reaching tasks. To the best of our knowledge, this work presents the first fully markerless pose-estimation-driven position-based visual servoing framework for continuum manipulators, enabling precise closed-loop control without physical markers or embedded sensing.

Myeongbo Park, Chunggil An, Junhyun Park et al.

Tendon-sheath mechanisms (TSMs) are widely used in minimally invasive surgical (MIS) applications, but their inherent hysteresis-caused by friction, backlash, and tendon elongation-leads to significant tracking errors. Conventional modeling and compensation methods struggle with these nonlinearities and require extensive parameter tuning. To address this, we propose a vibration-assisted hysteresis compensation approach, where controlled vibrational motion is applied along the tendon's movement direction to mitigate friction and reduce dead zones. Experimental results demonstrate that the exerted vibration consistently reduces hysteresis across all tested frequencies, decreasing RMSE by up to 23.41% (from 2.2345 mm to 1.7113 mm) and improving correlation, leading to more accurate trajectory tracking. When combined with a Temporal Convolutional Network (TCN)-based compensation model, vibration further enhances performance, achieving an 85.2% reduction in MAE (from 1.334 mm to 0.1969 mm). Without vibration, the TCN-based approach still reduces MAE by 72.3% (from 1.334 mm to 0.370 mm) under the same parameter settings. These findings confirm that vibration effectively mitigates hysteresis, improving trajectory accuracy and enabling more efficient compensation models with fewer trainable parameters. This approach provides a scalable and practical solution for TSM-based robotic applications, particularly in MIS.

Junhyun Park, Seonghyeok Jang, Myeongbo Park et al.

Cable-Driven Continuum Manipulators (CDCMs) enable scar-free procedures but face limitations in workspace and control accuracy due to hysteresis. We introduce an extensible CDCM with a Semi-active Mechanism (SAM) and develop a real-time hysteresis compensation control algorithm using a Temporal Convolutional Network (TCN) based on data collected from fiducial markers and RGBD sensing. Performance validation shows the proposed controller significantly reduces hysteresis by up to 69.5% in random trajectory tracking test and approximately 26% in the box pointing task. The SAM mechanism enables access to various lesions without damaging surrounding tissues. The proposed controller with TCN-based compensation effectively predicts hysteresis behavior and minimizes position and joint angle errors in real-time, which has the potential to enhance surgical task performance.