Andrea A. Conti

Andrea Conti, Matteo Poggi, Filippo Aleotti et al.

Depth perception is pivotal in many fields, such as robotics and autonomous driving, to name a few. Consequently, depth sensors such as LiDARs rapidly spread in many applications. The 3D point clouds generated by these sensors must often be coupled with an RGB camera to understand the framed scene semantically. Usually, the former is projected over the camera image plane, leading to a sparse depth map. Unfortunately, this process, coupled with the intrinsic issues affecting all the depth sensors, yields noise and gross outliers in the final output. Purposely, in this paper, we propose an effective unsupervised framework aimed at explicitly addressing this issue by learning to estimate the confidence of the LiDAR sparse depth map and thus allowing for filtering out the outliers. Experimental results on the KITTI dataset highlight that our framework excels for this purpose. Moreover, we demonstrate how this achievement can improve a wide range of tasks.

Matteo Poggi, Andrea Conti, Stefano Mattoccia

This paper introduces a novel deep framework for dense 3D reconstruction from multiple image frames, leveraging a sparse set of depth measurements gathered jointly with image acquisition. Given a deep multi-view stereo network, our framework uses sparse depth hints to guide the neural network by modulating the plane-sweep cost volume built during the forward step, enabling us to infer constantly much more accurate depth maps. Moreover, since multiple viewpoints can provide additional depth measurements, we propose a multi-view guidance strategy that increases the density of the sparse points used to guide the network, thus leading to even more accurate results. We evaluate our Multi-View Guided framework within a variety of state-of-the-art deep multi-view stereo networks, demonstrating its effectiveness at improving the results achieved by each of them on BlendedMVG and DTU datasets.

Alessio Mingozzi, Andrea Conti, Filippo Aleotti et al.

The recent pandemic emergency raised many challenges regarding the countermeasures aimed at containing the virus spread, and constraining the minimum distance between people resulted in one of the most effective strategies. Thus, the implementation of autonomous systems capable of monitoring the so-called social distance gained much interest. In this paper, we aim to address this task leveraging a single RGB frame without additional depth sensors. In contrast to existing single-image alternatives failing when ground localization is not available, we rely on single image depth estimation to perceive the 3D structure of the observed scene and estimate the distance between people. During the setup phase, a straightforward calibration procedure, leveraging a scale-aware SLAM algorithm available even on consumer smartphones, allows us to address the scale ambiguity affecting single image depth estimation. We validate our approach through indoor and outdoor images employing a calibrated LiDAR + RGB camera asset. Experimental results highlight that our proposal enables sufficiently reliable estimation of the inter-personal distance to monitor social distancing effectively. This fact confirms that despite its intrinsic ambiguity, if appropriately driven single image depth estimation can be a viable alternative to other depth perception techniques, more expensive and not always feasible in practical applications. Our evaluation also highlights that our framework can run reasonably fast and comparably to competitors, even on pure CPU systems. Moreover, its practical deployment on low-power systems is around the corner.

Luca Bartolomei, Matteo Poggi, Fabio Tosi et al.

This paper presents a novel general-purpose guided stereo paradigm that mimics the active stereo principle by replacing the unreliable physical pattern projector with a depth sensor. It works by projecting virtual patterns consistent with the scene geometry onto the left and right images acquired by a conventional stereo camera, using the sparse hints obtained from a depth sensor, to facilitate the visual correspondence. Purposely, any depth sensing device can be seamlessly plugged into our framework, enabling the deployment of a virtual active stereo setup in any possible environment and overcoming the severe limitations of physical pattern projection, such as the limited working range and environmental conditions. Exhaustive experiments on indoor and outdoor datasets featuring both long and close range, including those providing raw, unfiltered depth hints from off-the-shelf depth sensors, highlight the effectiveness of our approach in notably boosting the robustness and accuracy of algorithms and deep stereo without any code modification and even without re-training. Additionally, we assess the performance of our strategy on active stereo evaluation datasets with conventional pattern projection. Indeed, in all these scenarios, our virtual pattern projection paradigm achieves state-of-the-art performance. The source code is available at: https://github.com/bartn8/vppstereo.

Andrea Conti, Matteo Poggi, Valerio Cambareri et al.

Time-of-Flight (ToF) sensors provide efficient active depth sensing at relatively low power budgets; among such designs, only very sparse measurements from low-resolution sensors are considered to meet the increasingly limited power constraints of mobile and AR/VR devices. However, such extreme sparsity levels limit the seamless usage of ToF depth in SLAM. In this work, we propose ToF-Splatting, the first 3D Gaussian Splatting-based SLAM pipeline tailored for using effectively very sparse ToF input data. Our approach improves upon the state of the art by introducing a multi-frame integration module, which produces dense depth maps by merging cues from extremely sparse ToF depth, monocular color, and multi-view geometry. Extensive experiments on both synthetic and real sparse ToF datasets demonstrate the viability of our approach, as it achieves state-of-the-art tracking and mapping performances on reference datasets.